32 mm Square Drive Open End Head, J-Shank – QJOM32

The open end head QJOM32 belongs to the Snap-on interchangeable metric open end heads range, and Lost in HCM supplies it to workshops and factories across Vietnam. It uses the J (0.425") shank size, so it fits handles built for that shank. The center of fastener to retaining pin is QJOM Series – 2.50".

Open end head QJOM32 overview

The open end head QJOM32 is a metric open end head for interchangeable head torque wrenches. Its open jaw slides onto a nut or fitting from the side. So you can torque fasteners where a socket cannot drop over the top.

Snap-on builds this family in the USA in four shank sizes: J, Y, X, and Z. Listed sizes start at 6 mm on the J shank. Meanwhile, the large Z-shank heads reach 70 mm and carry ratings up to 480 ft-lb.

Its maximum recommended working torque is 60 ft-lb, about 81.3 N·m. The size is 32. Snap-on lists the country of origin as USA.

The o.d. is 65 mm. The head depth is 14 mm.

Specifications at a glance

The table below follows the Snap-on data for QJOM32. In addition, we converted imperial torque values to N·m where Snap-on lists none.

How the open end head works

An interchangeable head torque wrench has a socket at the end of its tube instead of a fixed ratchet. You slide the head shank into that socket until the retaining pin locks it. Then the wrench measures torque through the head, so the click still marks your set value.

The open end head itself is a jaw with two parallel faces. First, you slide the jaw onto the flats of the nut from the side. Next, you pull the handle at a steady pace until the wrench clicks, and you stop right away.

Key features of the open end head QJOM32

Every head in this family shares the same design logic, from the open jaw to the published torque limit. Here are the features that matter most when you compare options.

• Metric open jaw design. The open jaw slides onto a nut from the side, so you can reach fasteners on installed lines and rods. Sizes follow metric flats, which suits most Asian and European machines.
• Four shank sizes. The family comes in J (0.425 inch), Y (0.560 inch), X (0.735 inch), and Z (0.990 inch) shanks. Therefore, you can match light, medium, and heavy work to the right wrench body.
• Published working torque limits. Snap-on lists a maximum working torque for most sizes. Ratings run from 5 ft-lb on small J heads up to 480 ft-lb on Z heads. So you always know the safe limit.
• Wide metric size range. Listed sizes run from 6 mm on the J shank to 70 mm on the Z shank. Because of this, a few wrench bodies and a set of heads cover most metric nuts in a plant.
• Known center-to-pin distance. Each series lists the distance from the fastener center to the retaining pin. As a result, you can check the wrench manual and apply any setting correction with confidence.
• Dual-pin Z-shank options. Some large Z-shank heads come in dual-pin versions, marked DP in the part number. These heavy heads suit large nuts, and some carry a field-repairable warranty instead of a lifetime term.

Typical applications

These heads solve one problem well: torquing a nut that only allows side access. Below are typical jobs where that matters, from hydraulic fittings to jam nuts and large cylinder nuts.

• Hydraulic fitting hex bodies. Hydraulic adapters and valve bodies often have large hex flats behind a hose. An open end head slides onto those flats from the side, so you reach the spec without removing the hose.
• Jam nuts and lock nuts. Tie rods, adjusters, and threaded rods use jam nuts that sit on a long thread. Because a socket cannot pass over the rod, an open end head is often the only calibrated option.
• Machine adjustment nuts. Presses, conveyors, and molding machines use metric adjustment nuts that need a set torque. For example, a J-shank head gives fine control on small nuts below 60 ft-lb.
• Heavy hydraulic cylinders. Large cylinders on presses and loaders use big metric nuts and fittings. The X and Z-shank heads suit this work, since their ratings reach 240 to 480 ft-lb.
• Pipe and instrument fittings. Compression and instrument fittings need steady torque to seal without crushing the ferrule. Therefore, technicians use small open end heads with preset wrenches for repeat results.
• Assembly line torque checks. On production lines, a preset wrench with an open end head gives every operator the same result. In addition, the click signal makes each tightened joint easy to confirm and record.

Industries that use the open end head QJOM32

Metric open end heads matter wherever nuts sit behind tubing, rods, or brackets. The industries below rely on them every day. Many of these teams also work in FDI plants and service centers across Vietnam.

• Automotive manufacturing. Car and motorbike plants use metric fasteners on brake, steering, and fuel systems. In Vietnam, FDI assembly plants often need documented torque values, so calibrated heads help them pass customer audits.
• Heavy equipment maintenance. Excavators, cranes, and forklifts from Japan and Korea use large metric hydraulic fittings. For this reason, contractors in Vietnam use X and Z-shank heads to tighten high-load joints with control.
• Electronics and machine building. Machine builders that supply electronics plants assemble frames, guides, and actuators with metric nuts. Bac Ninh and Hai Phong plants also need tools that leave a clear torque record for ISO audits.
• Factory maintenance. Plants in Binh Duong, Dong Nai, and Long An run presses, pumps, and conveyors with metric parts. So maintenance teams keep open end heads to torque nuts that sockets cannot reach.
• Energy and power plants. Turbines, pumps, and compressors use metric fittings on lube oil and cooling lines. Power plant crews in Vietnam use open end heads to hit the stated torque during planned outages.
• Oil, gas, and process plants. Refineries and chemical plants rely on valves and instrument lines with hex fittings. Therefore, process teams use calibrated open end heads to seal joints without guesswork or damaged flats.

Open end head QJOM32 compared with similar brands

Before you buy, it helps to see how the open end head QJOM32 compares with other head systems. However, the key question is not the head alone. Instead, it is whether the head fits the wrench bodies your team already owns.

If your team already uses Snap-on or CDI interchangeable head wrenches, these heads are the simplest choice. They lock into the bodies you own and carry published limits. Even so, confirm current specs with each maker before you compare head ranges. Specifications change over time, so confirm current data with each maker before you decide.

Choosing the right model

• Start with the shank of your wrench body. A J-shank wrench takes only J-shank heads, while an X or Z-shank wrench needs its own matching heads.
• Measure the nut across its flats before ordering. Metric and inch sizes can look close, but a loose jaw will round the corners under torque.
• Compare the joint spec with the head rating. For example, a 150 ft-lb spec needs a Y, X, or Z-shank head, because J-shank heads top out at 60 ft-lb.
• Check the side clearance around each nut before you choose a head. If a hose or bracket sits close, pick the size with the smallest head depth that fits.
• Note the center-to-pin distance of each head. Then check the wrench manual to see whether the dial setting needs a correction for that head.
• Read the warranty line on each product page. Most heads carry a lifetime warranty, but some large dual-pin heads list a field-repairable term instead.

For other sizes in the same range, compare 30 mm Square Drive Open End Head, Y-Shank – QYOM30A, 18 mm Square Drive Open End Head, Y-Shank – QYOM18A, 20 mm Square Drive Open End Head, J-Shank – QJOM20A, 22 mm Square Drive Open End Head, Y-Shank – QYOM22A. Also browse the full Snap-on torque tools shop for handles, testers and adapters.

Care, storage and calibration

• Store each head in a drawer slot or case, away from loose tools. Then the jaw faces and shank stay free of nicks that affect fit.
• Wipe off oil, grease, and dirt after each job with a dry cloth. Also check the jaw faces for burrs, because a burr can mark soft fittings.
• Send the wrench body for calibration every 12 months or 5,000 cycles, as ISO 6789-1:2017 recommends. We can arrange recalibration through an accredited laboratory.
• Never set the wrench above the head's maximum working torque. Too much load can spread the jaw, so retire any head that shows a widened opening.
• Pack heads in a padded case for transport between sites. In addition, keep them dry during the humid season so the finish and shank stay clean.

Frequently asked questions

Request a quote

Send us the part number, quantity and delivery site, and we will reply with a quote. You can request a quote online or call 0902 327 669.