Tektronix TPR4000 Active Power Rail Probe

The Tektronix TPR4000 rental Vietnam service from Lost in HCM gives engineering teams in Vietnam short-term access to this oscilloscope probe, with sale and service options on request.

Tektronix TPR4000 rental Vietnam overview

Every scope reading starts at the probe tip, not at the screen. The Tektronix TPR4000 rental Vietnam gives your team the right link for each signal type. For example, that could be a fast serial lane or a floating gate drive. As a result, measurements stay accurate, safe, and repeatable across projects.

Lost in HCM offers these probes and accessories for rent or sale on a quote basis. Rental units ship with a valid calibration certificate where the maker specifies one. In addition, we can arrange service through the manufacturer or an authorized partner for probes you own.

Tektronix TPR4000 rental Vietnam: about the TPR4000

Tektronix TPR4000 rental Vietnam: tektronix TPR4000 overview

The Tektronix TPR4000 is an active power rail probe with 4 GHz bandwidth. Select this model as part of a complete probe, accessory and oscilloscope measurement path.

Tektronix TPR4000 rental Vietnam: product images

Tektronix TPR4000 rental Vietnam: specifications

Manufacturer	Tektronix
Model	TPR4000
Product type	Active Power Rail Probe
Bandwidth	4 GHz
Oscilloscope interface	TekVPI; verify exact oscilloscope compatibility
Attenuation	1.25X
DC offset range	±60 V
Input dynamic range	±1 V
Input impedance	50 kΩ DC; 50 Ω AC
Input coupling	DC or LF reject
Standard accessory kit	TPR4KIT; confirm current supplied contents

Tektronix TPR4000 rental Vietnam: measurement applications

Inspect ripple and fast disturbances on DC power rails. Start with a stable connection close to the load and compare captures using the same bandwidth limit and vertical scale. Include the expected DC rail voltage and ripple amplitude when specifying the measurement setup.

Connection schematic

DC power rail test point → rated tip / coax connection → TPR4000
Local circuit ground → short probe ground return
TPR4000 → compatible TekVPI oscilloscope → ripple waveform

Illustrative application connection schematic. Follow the current manufacturer manual for input ratings, grounding and accessory installation. Maximum nondestructive voltage is a protection limit and does not extend the specified measurement range. Teams in Vietnam often choose Tektronix TPR4000 rental for this reason.

Setup and compatibility

Use a compatible TekVPI oscilloscope and a connection rated for the rail voltage and environment. Set offset to center the rail, then choose vertical scale for ripple. The ±60 V offset range and ±1 V dynamic range describe different operating limits.

Request a quotation in Vietnam

Request a quotation for Tektronix TPR4000. Include the oscilloscope model, signal bandwidth, voltage levels, connection geometry and required accessories. Price, condition and local availability are confirmed individually.

Manufacturer reference

Official Tektronix datasheet. Specifications reviewed 20 October 2026; consult the full document for test conditions and frequency derating.

How the oscilloscope probe works

TriMode probes from Tektronix measure differential, single-ended, and common-mode signals through one tip connection. So engineers can switch modes from the scope without moving the probe. That saves time and solder joints on dense boards with fine-pitch parts. This applies to every Tektronix TPR4000 rental we arrange in Vietnam.

IsoVu probes break the ground path with an optical, fiber-based link. Therefore, they reject the large common-mode swings found in half-bridge and GaN circuits. Meanwhile, optical converters turn light signals into voltage for the scope. Logic probes also add digital channels next to the analog inputs.

What to look for in an oscilloscope probe

Before you rent or buy, note the signal speed, voltage level, and ground reference. Then check which scope interface your bench uses. Next, the features below explain what to compare, from bandwidth and loading to ratings and accessories.

• Bandwidth and rise time. The probe and scope together set the system bandwidth. So choose a probe rated well above your fastest edge, because a slow probe rounds edges and hides overshoot.
• Low circuit loading. Every probe adds resistance and capacitance to the circuit under test. Therefore, low-capacitance active probes suit fast or high-impedance nodes, while passive probes suit general bench work. So, plan it early when you book a Tektronix TPR4000 rental in Vietnam.
• Voltage rating and safety category. High-voltage probes list a maximum input and a CAT rating for each range. So check both against your circuit before you connect, especially on mains and inverter work.
• Differential and common-mode rejection. Differential probes measure between two points that both float above ground. As a result, good common-mode rejection matters, and isolated IsoVu probes push that rejection further on fast switching nodes.
• Scope interface and compatibility. Probes connect through BNC, TekVPI, TekConnect, or other maker interfaces. Therefore, confirm that the probe, any adapter, and your scope model work together before you plan a test.
• Tips, adapters, and accessories. Tips, cables, and adapters change how a probe reaches the circuit. For example, solder-in tips, SMA adapters, and MMCX tips suit different boards, so plan accessories with the probe. Our Tektronix TPR4000 rental units in Vietnam ship ready for this kind of work.

Typical applications

Each task below needs a probe that fits the signal, the voltage, and the ground reference. Then the scope can show what the circuit really does. Here is how teams in Vietnam use these probes every day.

• Power converter and inverter design. Switching stages create fast edges on nodes that float far above ground. So engineers use high-voltage differential or isolated probes to view gate drives and switch nodes safely.
• Wide-bandgap GaN and SiC testing. GaN and SiC devices switch very fast with large common-mode swings. Therefore, isolated probes with shunt tips help teams measure high-side signals and currents with less distortion.
• High-speed serial validation. Serial lanes such as PCIe and USB need high-bandwidth differential probing and low loading. For example, TriMode probes with solder-in tips capture eye diagrams without reworking the board between modes. Rental of the Tektronix TPR4000 is available across Vietnam.
• Power rail and ripple checks. Modern processors run on low-voltage rails with tight noise limits. As a result, low-noise probes with offset let engineers see small ripple on top of a DC level.
• Optical link testing. Fiber transceivers and optical modules send data as light, not voltage. So optical-to-electrical converters let a scope show pulse shape and eye patterns from those lanes.
• Embedded and mixed-signal debug. Firmware bring-up often needs digital buses and analog rails on one timebase. Therefore, logic probes add digital channels, while passive probes cover clocks, resets, and analog rails.

Industries that use the Tektronix TPR4000 rental Vietnam

Any site that designs, builds, or services electronics needs good probes. In Vietnam, demand comes mostly from FDI plants and R&D centers. The sectors below rent and buy probes most often, for design, production, and failure analysis. Teams in Vietnam often choose Tektronix TPR4000 rental for this reason.

• Electronics manufacturing services. EMS and ODM plants in northern and southern industrial parks run many test and rework benches. Therefore, they keep passive and active probes on hand and rent extra sets when a new product ramps.
• Power electronics and inverters. Makers of chargers, solar inverters, and motor drives work on fast, high-voltage switching. As a result, they rely on high-voltage differential and isolated probes for safe, clear readings.
• Automotive and EV. Vehicle electronics, battery systems, and EV traction drives need validation in the lab and on test rigs. For example, teams probe CAN lines, gate drives, and sensor outputs with suitable probes.
• Semiconductor and high-speed design. Chip, module, and high-speed board teams measure fast edges and signal integrity. So they pair high-bandwidth scopes with TriMode probes, solder-in tips, and optical converters. This applies to every Tektronix TPR4000 rental we arrange in Vietnam.
• Telecom and data center hardware. Network gear and optical modules combine fast electrical lanes with fiber links. Therefore, these teams use differential probes and optical-to-electrical converters side by side in the lab.
• Education and research. Universities and research institutes in Vietnam teach and test circuits in hands-on labs. Meanwhile, research projects often need a special probe for a few weeks, so rental fits well.

Tektronix TPR4000 rental Vietnam compared with other brands

Several makers build probe families for every voltage and speed range. However, each takes its own approach to bandwidth, isolation, and scope interface. The rows below show where the Tektronix TPR4000 rental Vietnam sits among other common probe choices in Vietnam labs.

Start from the signal type, the voltage level, and the ground reference. Next, weigh bandwidth, loading, and interface fit against your scope fleet. Because product lines change often, confirm current specs with each maker before you decide. Specifications change, so confirm current data with each maker before you decide.

Rent or buy?

Rent a probe for a design sprint, a compliance test, or a failure analysis. High-end probes such as TriMode and isolated models suit rental well, because teams need them for weeks, not years. Then you return them, so capital stays free for other work.

Selection tips

• Start with the ground reference of the signal you need to measure. If neither point sits at ground, choose a differential or isolated probe instead of a passive one. So, plan it early when you book a Tektronix TPR4000 rental in Vietnam.
• Choose probe bandwidth well above your fastest edge, because probe and scope together set system bandwidth. Also check the rise time in the maker's data.
• Check the maximum input voltage and CAT rating against your circuit. So you stay inside safe limits on mains, battery, and inverter work.
• Confirm the probe interface, such as BNC, TekVPI, or TekConnect, on your scope. Otherwise you may need an adapter, which can limit bandwidth or features.
• Plan tips and accessories with the probe itself. For example, solder-in tips, MMCX tips, and SMA adapters each suit a different test point.
• Pick low-capacitance active probes for fast or high-impedance nodes. Then keep passive probes for general bench work, where their range and toughness help most. Our Tektronix TPR4000 rental units in Vietnam ship ready for this kind of work.

Handling and care

• Handle probe tips and cables gently, and never pull a probe by its cable. Also store tips and adapters in their cases, because they bend and break easily.
• Wear an ESD strap before you touch active, TriMode, or isolated probe heads. Their input stages are sensitive, so static can damage them in an instant.
• Allow active probes and the scope to warm up as the manual advises. Next, compensate passive probes and run any deskew or offset routines before precise work.
• Follow the calibration interval each maker states for active and high-voltage probes. Rental units ship with a valid calibration certificate, and we can arrange service through the maker or an authorized partner.
• Ship probes in padded cases with cables coiled loosely and tips capped. In addition, keep fiber-based isolated probes dry and free of tight bends during Vietnam's humid wet season. Rental of the Tektronix TPR4000 is available across Vietnam.

Frequently asked questions

Request a quote

Tell us the model, options, dates and delivery site, and we will reply with a quote. You can request a quote online or call 0902 327 669. Teams in Vietnam often choose Tektronix TPR4000 rental for this reason.