Tektronix TRCP0600 AC Rogowski Current Probe

The Tektronix TRCP0600 rental Vietnam service from Lost in HCM gives engineering teams in Vietnam short-term access to this current probe, with sale and service options on request.

Tektronix TRCP0600 rental Vietnam overview

Current shows how hard a circuit really works, yet a voltage probe cannot see it directly. The Tektronix TRCP0600 rental Vietnam fills that gap on the bench, the line, and in the field. As a result, teams find overload, saturation, and timing faults much sooner.

Lost in HCM offers these probes, amplifiers, and shunts for rent or sale on a quote basis. Rental units ship with a valid calibration certificate. In addition, we can arrange service through the manufacturer or an authorized partner for units you own.

Tektronix TRCP0600 rental Vietnam: about the TRCP0600

Tektronix TRCP0600 rental Vietnam: tektronix TRCP0600 overview

The Tektronix TRCP0600 measures AC current with a flexible Rogowski sensing loop. Its specified bandwidth is 12 Hz to 30 MHz, with 600 A peak current capability under the manufacturer’s operating conditions.

Tektronix TRCP0600 rental Vietnam: product images

Tektronix TRCP0600 rental Vietnam: specifications

Manufacturer	Tektronix
Model	TRCP0600
Measurement type	AC only; does not measure DC
Bandwidth	12 Hz to 30 MHz
Current capability	600 A peak
Connection / required interface	1 MΩ BNC
Sensitivity	10 mV/A
Minimum current	500 mA
Coil cross-section diameter	4.5 mm
Typical accuracy	±2% of reading
Oscilloscope termination	1 MΩ

Current limits depend on frequency, pulse duration and operating conditions. Consult the manufacturer manual for derating and conductor-voltage ratings.

Tektronix TRCP0600 rental Vietnam: measurement applications

The flexible Rogowski loop can be positioned around a single conductor to observe changing current. It is useful for AC waveforms in power-conversion and motor-drive development. It cannot report a steady DC component. Position and close the coil as instructed in the manual, and use the stated output sensitivity when scaling the oscilloscope. Teams in Vietnam often choose Tektronix TRCP0600 rental for this reason.

Connection schematic

Single insulated DUT conductor → closed TRCP0600 sensing loop
Loop → probe electronics → oscilloscope BNC input (1 MΩ)
Probe power → specified supply

Illustrative connection diagram, not an internal service circuit. De-energize the circuit before fitting or removing the probe where required by the manual. Check conductor insulation, voltage category, jaw closure and current limits. Clamp around one conductor for its individual current; enclosing both supply and return can cancel their magnetic fields.

Setup and compatibility

Connect the probe electronics to a compatible 1 MΩ BNC input. Confirm the power arrangement, coil geometry and frequency range for the application. Peak current is not a continuous RMS rating.

Request a quotation in Vietnam

Request a quotation for Tektronix TRCP0600. Include your oscilloscope model, current range, waveform frequency, conductor size and required accessories. Price, condition and local availability are confirmed individually.

Manufacturer references

Official Tektronix datasheet. Reviewed 19 October 2026.

How the current probe works

A Rogowski probe uses a flexible air-core loop that wraps around large or awkward conductors. Because it has no iron core, it does not saturate on high currents. However, it measures AC only, so it suits drives, inverters, and power distribution checks. This applies to every Tektronix TRCP0600 rental we arrange in Vietnam.

A current shunt takes another path, because the current flows through a small known resistor. Then an isolated probe, such as a TICP IsoVu model, reads the voltage across it. So engineers can measure fast switching current while the probe stays isolated from high common-mode voltage.

What to look for in a current probe

Before you rent or buy, list the peak current, the fastest edge, and the conductor size. Then check whether you need DC. The features below explain what to compare, from bandwidth and range to interface, isolation, and safety ratings.

• AC only or AC and DC. AC-only probes and Rogowski loops skip DC, so they suit pulses and ripple. However, AC/DC models such as the TCP0030A and TCP303 also show DC offset, inrush, and slow load changes. So, plan it early when you book a Tektronix TRCP0600 rental in Vietnam.
• Bandwidth and rise time. Bandwidth sets the fastest current edge the probe can follow. For example, the CT6 reaches 2 GHz, and the TICP100 reaches 1 GHz. Meanwhile, the A621 stops at 50 kHz, which suits mains work.
• Current range and peak limits. Check both RMS or continuous current and the peak pulse limit. For instance, the TCP404XL handles 500 A DC continuous, while the CT6 handles 120 mA RMS. Also, respect amp-second limits on long pulses.
• Scope interface and power. TekVPI probes such as the TCP0020 and TCP0150 draw power from a compatible scope. However, the TCP303 needs a TCPA300 amplifier, and the CT probes need a 50 Ω input. So confirm the full system first.
• Jaw size and loop fit. The probe must close around your conductor without strain. For example, the A621 takes conductors up to 54 mm, while the CT6 takes a 0.8 mm wire. Flexible Rogowski loops also wrap around bus bars and thick cables. Our Tektronix TRCP0600 rental units in Vietnam ship ready for this kind of work.
• Isolation and shunt choice. IsoVu probes in the TICP family read current across a TICS shunt with galvanic isolation. Therefore, they suit high-side switching nodes. Shunt values from 5 mΩ to 5 Ω then set the current range and circuit loading.

Typical applications

Current probes appear wherever engineers must see how much current flows and when. The tasks below cover most rental and purchase requests in Vietnam. They range from power supply checks to motor drive, battery, and fast switching work.

• Power supply and inrush tests. Engineers capture inrush, ripple, and load steps on switch-mode supplies. So AC/DC probes like the TCP0030A show both the DC level and fast transients. As a result, teams confirm fuse and part ratings.
• Motor drive and inverter checks. Drives and inverters switch high currents in each phase. Therefore, engineers use TCP303, TCP404XL, or Rogowski probes on the phase leads. Then they compare current with gate signals on the same scope. Rental of the Tektronix TRCP0600 is available across Vietnam.
• GaN and SiC switching analysis. Wide-bandgap devices switch very fast at high voltage. So teams pair TICP IsoVu probes with TICS shunts in the power loop. That setup measures switching current while the probe stays isolated.
• Battery and EV current profiles. Battery packs and chargers draw large DC currents that change with load. For example, high-current AC/DC probes record charge and discharge profiles. In addition, the data supports efficiency and thermal studies.
• Pulse and noise troubleshooting. Fast current pulses often cause noise and false triggers in a system. So compact current transformers such as the CT1, CT2, and CT6 capture short spikes on thin wires. Engineers then trace the noise to its source.
• Mains and power quality work. Facility teams check load current on mains wiring and panels. Therefore, large clamps like the A621 and A622 and flexible TRCP loops suit this job. Always follow the CAT rating on each probe. Teams in Vietnam often choose Tektronix TRCP0600 rental for this reason.

Industries that use the Tektronix TRCP0600 rental Vietnam

Current probes matter in every business that designs, builds, or tests power electronics. The industries below rent and buy them most often in Vietnam. Many are FDI plants and R&D centers that serve large global brands.

• Power electronics. Makers of supplies, chargers, and inverters in Binh Duong and Dong Nai validate switching current every day. So they keep AC/DC probes on design benches. They also rent isolated probes and shunts for new GaN designs.
• Automotive and EV. EV, e-motorbike, and component plants in Vietnam test drives, chargers, and battery systems. Therefore, they need high-current AC/DC and Rogowski probes. Portable setups also help when engineers work at the vehicle.
• Electronics manufacturing services. EMS plants in Bac Ninh, Bac Giang, and Hai Phong measure board current during debug and failure analysis. As a result, compact AC/DC probes see daily use. Teams often rent extra units during production ramps. This applies to every Tektronix TRCP0600 rental we arrange in Vietnam.
• Renewable energy. Solar inverter and energy storage projects need current data on high-power converters. For example, flexible Rogowski loops wrap around thick cables and bus bars. Meanwhile, AC/DC probes check the DC link.
• Industrial automation. Factories run motors, drives, and servo systems that sometimes trip or overheat. So maintenance engineers use clamp probes to read phase current at the machine. This helps them find overload and imbalance faults.
• Education and research. Universities and research labs in Vietnam teach power electronics with hands-on tests. Therefore, they need safe, reliable current probes for many benches. Rental helps them equip a lab for one course or project.

Tektronix TRCP0600 rental Vietnam compared with other brands

Several makers build current probes for their own oscilloscopes and for general bench use. Each takes a different path on bandwidth, current range, and interface. The rows below show where the Tektronix TRCP0600 rental Vietnam sits among other common choices on the market.

If your team already uses Tektronix scopes, these probes connect with little new training. Other makers offer strong current probes too, especially for their own scopes. Even so, confirm current specs with each maker before you compare. Specifications change, so confirm current data with each maker before you decide.

Rent or buy?

Rent a current probe for a design validation, a failure analysis, or a short power study. Rental also gives access to high-current probes, IsoVu systems, and amplifiers for one project. Then you return them, so capital stays free for other test needs.

Selection tips

• Choose AC/DC when you need DC levels, inrush, or slow changes. Otherwise, an AC-only probe or a Rogowski loop may cover pulses and ripple well.
• Match bandwidth to your fastest current edge, not just the switching frequency. So fast GaN or SiC edges may need an isolated probe and shunt instead of a clamp. So, plan it early when you book a Tektronix TRCP0600 rental in Vietnam.
• Check peak, RMS, and continuous current limits together. Also review the amp-second limit for long pulses, because going past it can saturate the core.
• Confirm how the probe connects, such as TekVPI, BNC, or a separate amplifier. Then make sure your scope supports that interface and the needed input impedance.
• Measure the conductor or bus bar before you choose a jaw or loop size. For instance, thick cables may need a large clamp or a flexible Rogowski loop.
• For a shunt setup, pick a resistance that gives a usable voltage at your current. However, a higher value adds more loading and heat to the circuit.

Handling and care

• Close probe jaws gently and keep the core faces clean, because dirt adds error. Also store each probe, amplifier, and shunt in its case between jobs. Our Tektronix TRCP0600 rental units in Vietnam ship ready for this kind of work.
• Respect the voltage and CAT rating on every probe, since bare conductors can carry hazardous voltage. In addition, wear an ESD strap when you handle IsoVu tips and shunts.
• Let AC/DC probes warm up for the time the maker states. Next, degauss and zero the probe before precise DC readings, and repeat after any overload.
• Follow the calibration interval each maker states, which is often one year. Rental units ship with a valid calibration certificate, and we can arrange service through the maker or an authorized partner.
• Ship probes in padded cases with cables coiled loosely and jaws closed. In addition, keep them dry during Vietnam's humid wet season, because moisture harms sensors.

Frequently asked questions

Request a quote

Tell us the model, options, dates and delivery site, and we will reply with a quote. You can request a quote online or call 0902 327 669. Rental of the Tektronix TRCP0600 is available across Vietnam.