OE Torque Head Insert, 27 mm, 14 x 18 – IZ27OE14X18

The torque wrench insert IZ27OE14X18 belongs to the Snap-on IZO torque insert heads range, and Lost in HCM supplies it to workshops and factories across Vietnam. Snap-on lists the country of origin as Taiwan. The description (chart) is 27 mm OE insert 14 x 18.

Torque wrench insert IZ27OE14X18 overview

The torque wrench insert IZ27OE14X18 is a metric insert for IZO interchangeable head torque wrenches. It slides into the rectangular receiver at the end of the wrench body. Then the wrench reads torque through the insert, so one body can serve many fastener sizes.

Snap-on builds this family in Taiwan in two fitting sizes, 9 x 12 mm and 14 x 18 mm. Open-end inserts run from 7 mm up to 36 mm. Meanwhile, insert rings cover 10 mm to 36 mm, and a welding insert lets you build a custom end.

Specifications at a glance

The table below follows the Snap-on data for IZ27OE14X18. In addition, we converted imperial torque values to N·m where Snap-on lists none.

How the torque wrench insert works

Every insert moves the point of load a little away from the wrench body. Because of this, an insert with a different length can change the torque that reaches the bolt. That is why many wrench makers publish a correction for each insert length.

Some electronic bodies, such as ControlTech ISO models, also store a calibration factor for different head lengths. In short, you enter the insert data and the wrench does the math. Otherwise, you check the wrench manual and adjust the setting by hand.

Key features of the torque wrench insert IZ27OE14X18

The details below explain why these inserts fit tight spaces and protect fasteners. They also show what to check before you add a new insert to your current wrench set.

• Two standard fitting sizes. The family uses 9 x 12 mm and 14 x 18 mm rectangular fittings. So you can run light work on a small receiver and heavier joints on a larger body.
• Open-end inserts from 7 mm. Open-end inserts start at 7 mm on the small fitting. On the 14 x 18 mm fitting, they reach 36 mm. Therefore, one wrench set covers most metric nuts and bolts.
• Insert rings for a firm grip. Insert rings close fully around the fastener head instead of touching only two flats. As a result, they spread the load and lower the risk of rounding a tight nut.
• Welding insert for custom ends. The 9 x 12 mm welding insert gives toolmakers a blank end to weld a special tool on. For instance, a plant can build a custom reach end for one hard-to-access joint.
• Forged for strength. Snap-on lists forged construction for added strength and durability across this family. That matters because an insert carries the full torque load every time the wrench clicks or signals.
• Slim profile for tight spaces. The inserts suit areas where clearance is minimal, such as between a bracket and a housing. In addition, the open-end style slides onto a nut from the side when you cannot reach from above.

Snap-on data sheet notes

In addition, the Snap-on data sheet for IZ27OE14X18 notes:

• Interchangeable adaptors allow users to adapt to a multitude of applications easily and quickly.
• Forged construction for added strength and durability.
• Used in areas where there is minimal clearance.

Typical applications

A torque wrench insert earns its place where a fixed ratchet head cannot reach or fit. The tasks below are the most common uses we see from buyers in Vietnam.

• Hydraulic and pipe fittings. Open-end inserts reach the nuts on hydraulic hoses and pipe unions that a socket cannot cover. So technicians can torque these fittings on an installed line without removing nearby parts.
• Engine and gearbox assembly. Engine and gearbox builds use many metric bolts in tight spots. Therefore, a ring insert on a calibrated body lets one operator move from size to size and still hit each value.
• Production line torque stations. Assembly stations often need two or three sizes at one post. With IZO inserts, the operator swaps the end instead of the wrench, which keeps the torque record tied to one tool.
• Electrical cabinet terminals. Busbars and switchgear terminals need controlled torque to avoid loose joints and hot spots. In addition, the slim inserts fit between cables and panels where a ratchet head would not.
• Custom tools for special joints. Some joints need a bent, offset, or extended end that no catalog insert offers. For example, a toolroom can weld that shape onto the welding insert and keep the standard fitting.
• Maintenance on rail and machines. Rail cars, presses, and conveyors have large metric bolts that need regular checks. The 14 x 18 mm inserts up to 36 mm suit these jobs, while the smaller fitting covers guards and covers.

Industries that use the torque wrench insert IZ27OE14X18

Any sector with mixed metric fasteners gains from a wrench that swaps its end in seconds. So these inserts show up on assembly lines, in power plants, and in hangars. Here is how each industry uses them.

• Automotive assembly. Car and motorbike plants in Vietnam tighten many metric fasteners at every station. Many of these FDI lines use IZO bodies, so a full insert set keeps each station flexible and audit ready.
• Electronics and electrical. Electronics and switchgear makers in Bac Ninh and Hai Phong torque terminals, mounts, and frames. Therefore, small 9 x 12 mm inserts help them control light joints without stripping soft threads.
• Heavy equipment maintenance. Excavators, cranes, and mining trucks use large metric bolts and hydraulic fittings. For this reason, service teams across Vietnam pair 14 x 18 mm inserts with longer wrench bodies for these jobs.
• Energy and power plants. Power plants and wind farms run flange bolts, pump mounts, and cable lugs on a strict schedule. So maintenance crews use ring inserts to tighten these joints evenly and log the result.
• Aviation maintenance. Aircraft and engine work often calls for open-end access to tube nuts and brackets. Also, MRO teams at Vietnamese airports need tools with a clear torque record for each task card.
• General factory maintenance. Plants in Binh Duong, Dong Nai, and VSIP parks run European and Asian machines with metric bolts. Maintenance teams then use one calibrated body and a rack of inserts instead of many wrenches.

Torque wrench insert IZ27OE14X18 compared with similar brands

Several makers sell inserts for rectangular-fitting torque wrenches. Many use similar 9 x 12 mm and 14 x 18 mm sizes, but length and lock design can differ. The table below shows where the torque wrench insert IZ27OE14X18 sits among common choices.

Choose inserts that match your wrench bodies first, then compare size range and type. Snap-on covers open-end, ring, and welding styles in both fittings. Meanwhile, plants with mixed brands should confirm current specs with each maker before ordering. Specifications change over time, so confirm current data with each maker before you decide.

Choosing the right model

• Start with the receiver on your wrench body. A small receiver takes only 9 x 12 mm inserts, while a larger body needs the 14 x 18 mm fitting.
• Measure the fastener across its flats before you order. Metric sizes sit close together, so a loose insert can round the nut under load.
• Choose an insert ring when you can reach the fastener from above. Then pick an open-end insert only when a tube or cable blocks the ring.
• Match the insert to the torque you need. For example, heavy joints above the small body range belong on a 14 x 18 mm wrench and insert.
• Check the insert length against your wrench manual. If the length differs from the standard, apply the stated correction before you set a value.
• Plan a full rack of inserts for each wrench body. That way, operators swap ends at the station instead of grabbing an uncalibrated wrench.

For other sizes in the same range, compare Torque Head Insert Ring, 12 mm, 9 x 12 – IZ12IR9X12, OE Torque Head Insert, 17 mm, 9 x 12 – IZ17OE9X12, Torque Head Insert Ring, 30 mm, 14 x 18 – IZ30IR14X18, OE Torque Head Insert, 18 mm, 14 x 18 – IZ18OE14X18. Also browse the full Snap-on torque tools shop for handles, testers and adapters.

Care, storage and calibration

• Store each insert in a rack or case slot, away from loose tools. Then the fitting and jaws stay free of nicks that affect lock and grip.
• Wipe off oil, coolant, and dirt after each job with a dry cloth. Also check the jaws for burrs, because a burr can mark finished fasteners.
• Send the wrench body for calibration every 12 months or 5,000 cycles, as ISO 6789-1:2017 recommends. We can arrange recalibration through an accredited laboratory.
• Never load an insert past the range of the wrench body it sits in. Retire any insert with spread jaws, cracks, or a worn fitting.
• Pack inserts in a padded case for transport between sites. In addition, keep them dry during the humid season so the finish and fitting stay clean.

Frequently asked questions

Request a quote

Send us the part number, quantity and delivery site, and we will reply with a quote. You can request a quote online or call 0902 327 669.